Members Login
Username 
 
Password 
    Remember Me  
ECU hacking -> Suzuki GSX1300R Hayabusa Gen II -> ecueditor.com interface
Post Info TOPIC: ecueditor.com interface
jc001


Member

Status: Offline
Posts: 10
Date:
RE: ecueditor.com interface
Permalink  

Hi,

I'm building my interface V1.3, but I have a trouble ...confuse

Can you confirm R7?

On v1.3, R7 is 1Kom and on v1.2, R7 is 10Kom.

 

Thanks for your answer.



__________________
jc001


Member

Status: Offline
Posts: 10
Date:
Permalink  

No response,

I'm alone to have seen this problem....



__________________
jkwool


Guru

Status: Offline
Posts: 1233
Date:
Permalink  

sorry for the delay in getting back to you. the resistor should be 1k. early versions had a 10k resistor but to allow the fast baud rate the 1k resistor works better. the latest circuit diagram can be found here

http://ecueditorco.web713.discountasp.net//images/ecueditor_v1.3c.123

Cheers
-Justin.

__________________

site_logo_small.png

www.WoolichRacing.comTune your bike to the Limit with our Advanced ECU Flashing Products
jc001


Member

Status: Offline
Posts: 10
Date:
Permalink  

Ok thanks,

 

You confirm that R7 and R9 are 1 Kom?



__________________
jkwool


Guru

Status: Offline
Posts: 1233
Date:
Permalink  

jc001 wrote:

Ok thanks,

 

You confirm that R7 and R9 are 1 Kom?

 http://ecueditorco.web713.discountasp.net//images/ecueditor_v1.3c.123



__________________

site_logo_small.png

www.WoolichRacing.comTune your bike to the Limit with our Advanced ECU Flashing Products
jc001


Member

Status: Offline
Posts: 10
Date:
Permalink  

Ok i found my fault,

The first picture on page 1 is not the good emplacement for the resistances for the v1.3.

R7 is 10kom.

Thanks a lot.

Bye

__________________
incoldblood


Member

Status: Offline
Posts: 19
Date:
Permalink  

I use a 1N4007 Diode its the same?

 

Finally what the difference from v1.2 to v1.3?

 

R7 on v1.3 is 1K



-- Edited by incoldblood on Tuesday 3rd of April 2012 09:28:25 AM



-- Edited by incoldblood on Tuesday 3rd of April 2012 09:45:54 AM

__________________
incoldblood


Member

Status: Offline
Posts: 19
Date:
Permalink  

Who can help me????

I don't know why it don't work.

I connect 12v 600mA external power but led and ecu editor don't work

i'll try to upload son photo

 

Ecu editor write

 

"Interface is not on or it is not in programming mode, set programming switch to programming mode and retry...

 HELP ME PLEASE :(



-- Edited by incoldblood on Wednesday 4th of April 2012 07:28:38 PM



-- Edited by incoldblood on Wednesday 4th of April 2012 07:34:26 PM

__________________
Brix


Senior Member

Status: Offline
Posts: 179
Date:
Permalink  

Hi

work out of Bike?

RX-TX and TX-RX

Sensorground from white Conector to Sensorgrd ECU



__________________

http://motorsport-brix.de/
incoldblood


Member

Status: Offline
Posts: 19
Date:
Permalink  

No, don't work. ecu editor write me Interface is not on or it is not in programming mode, set programming switch to programming mode and retry forever.

I have this cable http://it.rs-online.com/web/p/products/687-7786/

I said that is not powered.



__________________
Brix


Senior Member

Status: Offline
Posts: 179
Date:
Permalink  

The cable is correct.
Measure the voltage between red and black when it is connected to the PC.
Since you have to have 5 volts.



__________________

http://motorsport-brix.de/
incoldblood


Member

Status: Offline
Posts: 19
Date:
Permalink  

yes, i have 5v on red and black.

don't work out of bike, i don't try in the bike.

i think this cable have rx and tx inverted...

i want try when ecu is on the bike...but in yoshi plug, what is the wire that i use?

__________________
incoldblood


Member

Status: Offline
Posts: 19
Date:
Permalink  

i try with external 12v power but led light is smaller and alternate on-off


__________________
incoldblood


Member

Status: Offline
Posts: 19
Date:
Permalink  

probably i know the problems...
for programmer power i use a 12v power but i use this to charge my battery and i think its a different power from 220 to 12V...i think...

__________________
incoldblood


Member

Status: Offline
Posts: 19
Date:
Permalink  

In PCB 1.3C r7 is 10kohm and r9 1kohm its correct?

__________________
incoldblood


Member

Status: Offline
Posts: 19
Date:
Permalink  

Who can help me?

__________________
jarim


Veteran Member

Status: Offline
Posts: 82
Date:
Permalink  

Would someone have 5 pcs v1.3 boards laying around? Would be interested to buy. Would buy directly from Sunstone but for example 10pcs cost $131 and postage is $143 so a bit expensive...

__________________

- Jari // GSX1400R '0x // 355.1km/h / 9.193s -
incoldblood


Member

Status: Offline
Posts: 19
Date:
Permalink  

jarim wrote:

Would someone have 5 pcs v1.3 boards laying around? Would be interested to buy. Would buy directly from Sunstone but for example 10pcs cost $131 and postage is $143 so a bit expensive...

 jarim, write on my board your e-mail...i can help you!!



-- Edited by incoldblood on Thursday 26th of April 2012 12:41:31 PM

__________________
Nizzer450r


Newbie

Status: Offline
Posts: 2
Date:
Permalink  

Hi petrik 

(new to forum) looking at building my own interface for a gen 2 busa for a college project , but cannot view the JPEGs of your design. Can you help please ?

 

cheers 

neil



__________________
BKing111


Newbie

Status: Offline
Posts: 2
Date:
Permalink  

Hello guru,I know this is an old thread but i'd like to try and make my own interface.Is there any place to still get the schematics at online?  Thanks Gene

 



-- Edited by BKing111 on Saturday 15th of April 2017 05:29:14 AM

__________________
«First  <  1 2 3 | Page of 3  sorted by
 
Quick Reply

Please log in to post quick replies.
ECU hacking -> Suzuki GSX1300R Hayabusa Gen II -> ecueditor.com interface
Tweet this page Post to Digg Post to Del.icio.us


Create your own FREE Forum
Report Abuse 		Powered by ActiveBoard